Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Weight |
172.98879mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2001 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG201 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
12/+-15V |
Number of Channels |
1 |
Max Supply Voltage |
25V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
50μA |
Nominal Supply Current |
50μA |
Power Dissipation |
640mW |
Max Supply Current |
50μA |
Throw Configuration |
SPST |
Turn On Delay Time |
300 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
4.5V~25V ±4.5V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
300ns, 200ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Height |
920μm |
Length |
5.08mm |
Width |
4.4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG201BDQ-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 16 series. Unlike digital switches, these are based on SPST - NC switching circuits. Use DG201 to search for variants of the digital switches. There is 160Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 25V in normal situations. Analog switch ics with Dual, Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 4.5V. It would be sufficient to run this analogue multiplexer with 50μA current. A digital multiplexer may suffer damage if voltage is applied above 50μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. The voltage should be at least 4.5V if you are using dual power supplies. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Among the inputs that can be operated are the 4 inputs.
DG201BDQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
50μA Supply Current
DG201BDQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG201BDQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Data switching
- Avionics test equipment
- Channel Banks
- SONET
- Medical systems
- Automotive applications
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Transmit
- Audio signal routing
- SDH/SONET multiplexers