DG201BDY-T1
| Parameters | |
|---|---|
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 100μA |
| Power Dissipation | 640mW |
| Max Supply Current | 50μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
DG201BDY-T1 Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. An injection of 16 pins is performed into the body of the electrical component. SPST - NC switching circuits are used in these analog switch ics. A 85Ohm internal resistance characterizes this multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 25V voltage to the switch device. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 4.5V. If put voltage greater than 50μA on the device, damage may be caused to the analogue multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. If you are using dual power supplies, you should attach at least 4.5V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. In order to operate the 4 inputs, there are several steps to follow.
DG201BDY-T1 Features
1 Channels
Switch Circuit: SPST - NC
DG201BDY-T1 Applications
There are a lot of Vishay Siliconix DG201BDY-T1 Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Fiber In The Loop (FITL)
- Signal routing between systems
- Imaging
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- DVD-R
- Isolation
- Low-Voltage
