DG201BDY-T1-E3

300ns, 200ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG201 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG201BDY-T1-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 215
Description: 300ns, 200ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG201 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	640mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG201
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	24V
Power Supplies	12/+-15V
Number of Channels	1
Max Supply Voltage	25V
Min Supply Voltage	4.5V
Operating Supply Current	50μA
Nominal Supply Current	100μA
Power Dissipation	640mW
Max Supply Current	50μA
Throw Configuration	SPST
Turn On Delay Time	300 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	4.5V~25V ±4.5V~22V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	200 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	4.5V
Dual Supply Voltage	9V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	300ns, 200ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	85Ohm
Normal Position	NC
Height	1.55mm
Length	10mm
Width	4mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG201BDY-T1-E3 Overview

Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Into the electrical component body are injected 16 pins. These analog multiplexers are built based on SPST - NC switching circuits. Try searching for the analog switch ic with DG201 if you are looking for variants. There is 160Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 25V. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended that the electrical component receives a voltage of 4.5V. This multiplexer would work with 50μA current. The analogue multiplexer may be damaged if voltage is greater than 50μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. It is recommended that you attach at least 4.5V to your dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. There is a voltage range of 24V operating voltages for the electrical part. It is possible to operate 4 inputs. Drain to Source resistance is 85Ohm.