DG201HSDJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 16.5V |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 13V |
| Power Dissipation | 470mW |
| Max Supply Current | 10mA |
| Turn On Delay Time | 60 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 60ns, 50ns |
| Charge Injection | -5pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -100dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
| Factory Lead Time | 1 Week |
DG201HSDJ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 16 terminations. If the voltage supply is 15V volts, the electrical component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Based on SPST - NC switching circuits, these analog multiplexers work. Internally, this switch multiplexer has a resistance of 50Ohm. The functions of 16 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 25V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 13V. If you put voltage higher than 10mA on the digital multiplexer, damage may occur. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. When using dual power supplies, you should attach at least 7V. This analog switch ic utilizes SEPARATE OUTPUT output. The electronic component can function from 16.5V. There are 4 inputs to be operated.
DG201HSDJ Features
Switch Circuit: SPST - NC
DG201HSDJ Applications
There are a lot of Vishay Siliconix DG201HSDJ Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- Avionics test equipment
- Signal routing between systems
- Communication systems
- Private Branch Exchange (PBX)
- Cable Modem
- Video signal routing
- Communication systems
- Remote Powered Equipment
- MP3 players
