DG201HSDQ-T1-E3

60ns, 50ns SPST - NC 50Ohm Analog Switches BREAK-BEFORE-MAKE DG201 16 Pins 1nA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG201HSDQ-T1-E3
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 230
Description: 60ns, 50ns SPST - NC 50Ohm Analog Switches BREAK-BEFORE-MAKE DG201 16 Pins 1nA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.65mm
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG201
Output	SEPARATE OUTPUT
Pin Count	16
Qualification Status	Not Qualified
Operating Supply Voltage	16.5V
Number of Channels	1
Max Supply Voltage	25V
Min Supply Voltage	13V
Operating Supply Current	10mA
Nominal Supply Current	4.5mA
Power Dissipation	600mW
Max Supply Current	10mA
Throw Configuration	SPST
Turn On Delay Time	60 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	10.8V~16.5V ±15V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	50 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	50Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	85 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	5pF
On-state Resistance Match-Nom	0.75Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	60ns, 50ns
Charge Injection	-5pC
Channel-to-Channel Matching (ΔRon)	1.5 Ω
Crosstalk	-100dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Normal Position	NC
Height	920μm
Length	5.08mm
Width	4.4mm
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2009
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	90Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Technology	CMOS
Terminal Form	GULL WING

DG201HSDQ-T1-E3 Overview

Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around -40°C~85°C TA. In total, there have been 16 terminations. By its 1 channels, the electronic component provides high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. This electronic part can be found in the 16 series. On the other hand, analog switches can be constructed using SPST - NC switching circuits. Use DG201 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 90Ohm. You can find the functions of the 16 pins in the datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 25V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 13V. The analogue multiplexer could operate on 10mA current. When the digital multiplexer is charged above 10mA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. In the case of dual power supplies, you should connect at least 7V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. The electrical part can be operated at 16.5V voltage levels. It is possible to operate 4 inputs.