DG201HSDY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Bulk |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Pin Count | 16 |
| Operating Supply Voltage | 16.5V |
| Polarity | Inverting |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 4.5mA |
| Nominal Supply Current | 4.5mA |
| Power Dissipation | 600mW |
| Max Supply Current | 10mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 60 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 60ns, 50ns |
| Charge Injection | -5pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -100dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG201HSDY Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Bulk is used. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. A total of 16 terminations have been recorded. With a 15V voltage supply, the electrical component should be turned on and run. This electrical component is included in the 16 series of products. Unlike digital switches, these are based on SPST - NC switching circuits. The internal resistance of this digital multiplexer is 50Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. Digital switch that provides Dual, Single power at a cost-effective price. The lowest voltage fed to the electronic component should be 13V. In order to operate this switch device, it would need a current of 4.5mA. Putting voltage greater than 10mA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. You should attach at least 7V voltage if you are using dual power supply. It can operate from 16.5V operating voltages. It is possible to operate 4 inputs.
DG201HSDY Features
Switch Circuit: SPST - NC
4.5mA Supply Current
DG201HSDY Applications
There are a lot of Vishay Siliconix DG201HSDY Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Intelligent PBX
- Automotive applications
- FTTH
- Cell phones
- Fault Tolerant Systems
- USB 1.1 signal switching circuits
- Industrial and process control systems
- Cross Connects
- Audio/video switches
