DG202AK/883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Screening Level | MIL-STD-883 Class B |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 600ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG202AK/883B Overview
Packed in 16-CDIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. The advanced packaging method Tube provides high reliability. Multiplexers like this are mounted in the Through Hole position. Multiplexers and demultiplexers have a number of circuits 1:1. Increasing operating temperature to around -55°C~125°C TA. In total, 16 terminations have occurred. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. Electronic part bodies are injected with 16 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. It consists of 4 circuits. Internally, this switch multiplexer has a resistance of 175Ohm. The functions of 16 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 25V. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. In the case of dual power supplies, you should connect at least 4.5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
DG202AK/883B Features
1 Channels
Switch Circuit: SPST - NO
DG202AK/883B Applications
There are a lot of Maxim Integrated DG202AK/883B Analog Switches & Multiplexers ICs applications.
- Medical
- Microprocessor controlled systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Private Branch Exchange (PBX)
- Fault Tolerant Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Audio and video switching
- Digital access cross connects
- Audio and video signal routing
- Transmit
