banner_page

DG202BDJ

300ns, 200ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 16-DIP (0.300, 7.62mm)


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG202BDJ
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 986
  • Description: 300ns, 200ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Through Hole
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Number of Pins 16
Weight 1.627801g
Operating Temperature -40°C~85°C TA
Packaging Tube
Published 2014
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
Resistance 85Ohm
Terminal Finish Tin/Lead (Sn/Pb)
Subcategory Multiplexer or Switches
Max Power Dissipation 470mW
Technology CMOS
Number of Functions 4
Output SEPARATE OUTPUT
Pin Count 16
Power Supplies 12/+-15V
Max Supply Voltage 25V
Min Supply Voltage 4.5V
Power Dissipation 470mW
Max Supply Current 50μA
Turn On Delay Time 300 ns
Number of Inputs 4
Voltage - Supply, Single/Dual (±) 4.5V~25V ±4.5V~22V
Supply Type Dual, Single
Turn-Off Delay Time 200 ns
Max Dual Supply Voltage 22V
On-State Resistance (Max) 85Ohm
Min Dual Supply Voltage 4.5V
Multiplexer/Demultiplexer Circuit 1:1
Current - Leakage (IS(off)) (Max) 500pA
Channel Capacitance (CS(off), CD(off)) 5pF 5pF
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 300ns, 200ns
Charge Injection 1pC
Channel-to-Channel Matching (ΔRon) 2 Ω
Crosstalk -95dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Drain to Source Resistance 85Ohm
Normal Position NO
Height 3.81mm
Length 21.33mm
Width 7.11mm
Radiation Hardening No
RoHS Status Non-RoHS Compliant

DG202BDJ Overview


Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Through Hole, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. The total number of terminations is 16. As part of the design of the 16 series, this electronic part has been incorporated into the system. A SPST - NO switching circuit is used for these analog switches. In this multiplexer, the internal resistance is 85Ohm. Please refer to the datasheets for 16 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 25V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Dual, Single supply type. A low voltage of 4.5V should be applied to the electronic component. Put voltage above 50μA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. With dual power supplies, you should attach at least 4.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. In order to operate the 4 inputs, there are several steps to follow. Drain to Source resistance for this electronic component is 85Ohm.

DG202BDJ Features


Switch Circuit: SPST - NO
Drain-to-Source resistance: 85Ohm

DG202BDJ Applications


There are a lot of Vishay Siliconix DG202BDJ Analog Switches & Multiplexers ICs applications.

  • Channelized and Unchannelized DS3 applications
  • Signal routing between systems
  • USB 1.1 signal switching circuits
  • High speed data transmission line cards
  • Frame Relay Equipment
  • CSU
  • High-Voltage
  • Sample hold systems
  • Routers
  • Video switching

Write a review

Note: HTML is not translated!
    Bad           Good