DG202BDJ-E3

300ns, 200ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG202 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG202BDJ-E3
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 761
Description: 300ns, 200ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG202 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Weight	1.627801g
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2013
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	470mW
Technology	CMOS
Number of Functions	4
Supply Voltage	15V
Base Part Number	DG202
Output	SEPARATE OUTPUT
Pin Count	16
Power Supplies	12/+-15V
Number of Channels	1
Max Supply Voltage	25V
Min Supply Voltage	4.5V
Operating Supply Current	50μA
Nominal Supply Current	50μA
Power Dissipation	470mW
Max Supply Current	50μA
Throw Configuration	SPST
Turn On Delay Time	300 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	4.5V~25V ±4.5V~22V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	200 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	300ns, 200ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	85Ohm
Normal Position	NO
Height	3.81mm
Length	21.33mm
Width	7.11mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG202BDJ-E3 Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around -40°C~85°C TA. In total, 16 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. It is injected into the electrical part body with 16 pins. SPST - NO switching circuits are used in these analog switch ics. Try searching for DG202 variants of the analog switch ic. It has an internal resistance of 160Ohm. For details about the functions of 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 25V in normal situations. A cost-effective Dual, Single supply type analogue multiplexer. There should be 4.5V voltage fed to the electrical part below 4.5V. In order to operate this switch device, it would need a current of 50μA. If you put voltage higher than 50μA on the digital multiplexer, damage may occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. It is recommended that you attach at least 4.5V to your dual power supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. It is possible to operate 4 inputs. Resistivity from Drain to Source is 85Ohm for this electronic part.