Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Bulk |
Published |
2016 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG202 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
22V |
Power Supplies |
12/+-15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
25V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
50μA |
Nominal Supply Current |
50A |
Throw Configuration |
SPST |
Voltage - Supply, Single/Dual (±) |
4.5V~25V ±4.5V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
300ns, 200ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
300ns |
Switch-off Time-Max |
200ns |
Normal Position |
NO |
Height Seated (Max) |
1.2mm |
Length |
5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG202BDQ-E3 Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Bulk is used. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. Totally, there are 16 terminations. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. There are 16 pins injected into the electronic part body. On the other hand, analog switches can be constructed using SPST - NO switching circuits. A total of 4 circuits make up this switch device. Use DG202 to search for variants of the digital switches. As far as internal resistance is concerned, it has 160Ohm. Datasheets for 16 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 4.5V should be applied to the electronic component. This multiplexer would work with 50μA current. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. With dual power supplies, you should attach at least 4.5V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating voltages range from 22V.
DG202BDQ-E3 Features
1 Channels
Switch Circuit: SPST - NO
50μA Supply Current
DG202BDQ-E3 Applications
There are a lot of Vishay Siliconix DG202BDQ-E3 Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Fault Tolerant Systems
- Industrial control systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Communication systems
- Audio/video switches
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Routers
- Central office