DG202BDQ-T1-E3

300ns, 200ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG202 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG202BDQ-T1-E3
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 275
Description: 300ns, 200ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG202 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2013
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	640mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG202
Output	SEPARATE OUTPUT
Pin Count	16
Power Supplies	12/+-15V
Number of Channels	1
Max Supply Voltage	25V
Min Supply Voltage	4.5V
Operating Supply Current	50μA
Nominal Supply Current	50μA
Power Dissipation	640mW
Max Supply Current	50μA
Throw Configuration	SPST
Turn On Delay Time	300 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	4.5V~25V ±4.5V~22V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	200 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	300ns, 200ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	85Ohm
Normal Position	NO
Height	920μm
Length	5.08mm
Width	4.4mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG202BDQ-T1-E3 Overview

Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. 16 pins are injected to the electronic part body. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching for the analog switch ic with DG202 if you are looking for variants. As far as internal resistance is concerned, it has 160Ohm. You can find the functions of the 16 pins in the datasheets. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 25V. Dual, Single supply type digital switch with a low cost. It is recommended to use 4.5V as the lowest voltage for the electrical part. 50μA current would be enough for this multiplexer to operate. If put voltage greater than 50μA on the device, damage may be caused to the analogue multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIn the case of dual power supplies, you should connect at least 4.5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Operating 4 inputs is required. It has a Drain to Source resistance of 85Ohm ohms.