banner_page

DG202BDY

300ns, 200ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 16-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG202BDY
  • Package: 16-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 308
  • Description: 300ns, 200ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 16-SOIC (0.154, 3.90mm Width)
Number of Pins 16
Weight 665.986997mg
Operating Temperature -40°C~85°C TA
Packaging Bulk
Published 2016
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
Resistance 85Ohm
Terminal Finish Tin/Lead (Sn/Pb)
Subcategory Multiplexer or Switches
Max Power Dissipation 640mW
Technology CMOS
Terminal Form GULL WING
Number of Functions 4
Terminal Pitch 1.27mm
Output SEPARATE OUTPUT
Pin Count 16
Power Supplies 12/+-15V
Max Supply Voltage 25V
Min Supply Voltage 4.5V
Power Dissipation 640mW
Max Supply Current 50μA
Turn On Delay Time 300 ns
Number of Inputs 4
Voltage - Supply, Single/Dual (±) 4.5V~25V ±4.5V~22V
Supply Type Dual, Single
Turn-Off Delay Time 200 ns
Max Dual Supply Voltage 22V
On-State Resistance (Max) 85Ohm
Min Dual Supply Voltage 4.5V
Multiplexer/Demultiplexer Circuit 1:1
Current - Leakage (IS(off)) (Max) 500pA
Channel Capacitance (CS(off), CD(off)) 5pF 5pF
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 300ns, 200ns
Charge Injection 1pC
Channel-to-Channel Matching (ΔRon) 2 Ω
Crosstalk -95dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Drain to Source Resistance 85Ohm
Normal Position NO
Height 1.55mm
Length 10mm
Width 4mm
Radiation Hardening No
REACH SVHC Unknown
RoHS Status Non-RoHS Compliant

DG202BDY Overview


The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. The operating temperature is extended to around -40°C~85°C TA. 16 terminations have been made so far. As part of the design of the 16 series, this electronic part has been incorporated into the system. A SPST - NO switching circuit is used for these analog switches. This digital multiplexer has 85Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended that the electrical component receives a voltage of 4.5V. Putting voltage greater than 50μA on the multiplexer may cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. It is recommended that you attach at least 4.5V to your dual power supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. It is possible to operate 4 inputs. There is 85Ohm resistance between the Drain and Source on this part.

DG202BDY Features


Switch Circuit: SPST - NO
Drain-to-Source resistance: 85Ohm

DG202BDY Applications


There are a lot of Vishay Siliconix DG202BDY Analog Switches & Multiplexers ICs applications.

  • Cell phones
  • FTTH
  • Channelized and Unchannelized DS3 applications
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • E1 Multiplexer
  • Cable Modem
  • Wireless Local Loop
  • Precision instrumentation
  • Digital Cross-Connects
  • Audio and video switching

Write a review

Note: HTML is not translated!
    Bad           Good