DG202BDY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 50μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG202BDY-T1 Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 16. A 1 channel electronic part produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. A SPST - NO switching circuit is used for these analog switches. It consists of 4 circuits. It has an internal resistance of 85Ohm. You can find the functions of the 16 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. Analogue multiplexer with a Dual, Single supply type that is cost-effective. A low voltage of 4.5V should be applied to the electronic component. A digital multiplexer may suffer damage if voltage is applied above 50μA. For this switch, a dual supply voltage is feasible, but it must not exceed 22VYou should attach at least 4.5V voltage if you are using dual power supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG202BDY-T1 Features
1 Channels
Switch Circuit: SPST - NO
DG202BDY-T1 Applications
There are a lot of Vishay Siliconix DG202BDY-T1 Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- Sample hold systems
- Fault Tolerant Systems
- Medical Instrumentation
- New designs requiring multiplexer functions
- Battery Powered Instruments
- Medical
- PBX interfaces
- Access Concentrators
- Public switching systems
