DG202CJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG202 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 25V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG202CJ+ Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around 0°C~70°C TA. The total number of terminations is 16. Due to its 4 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 16 series. A SPST - NO switching circuit is used for these analog switches. Look for analog switch ic variants by searching with DG202. A 200Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 25V. The digital multiplexer has a low cost Dual supply. For this multiplexer to operate, 20μA current would be sufficient. A digital multiplexer may suffer damage if voltage is applied above 20μA. Despite this switch device's dual supply capability, its voltage should not exceed 18V. It is recommended that you attach at least 4.5V to your dual power supply. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating voltages range from 18V.
DG202CJ+ Features
4 Channels
Switch Circuit: SPST - NO
20μA Supply Current
DG202CJ+ Applications
There are a lot of Maxim Integrated DG202CJ+ Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- Central office
- Cellular phones
- DSLAMs
- Frame Relay Equipment
- Remote Powered Equipment
- FTTH
- Modems
- Intelligent PBX
- Fiber In The Loop (FITL)
