DG202CSE+
| Parameters | |
|---|---|
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG202 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Nominal Supply Current | 20μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
DG202CSE+ Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around 0°C~70°C TA is the extended operating temperature. In total, there have been 16 terminations. Due to its 1 channels, the electrical component produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 16 pins. The analog switch ics are built using SPST - NO switching circuits. This multiplexer is composed of 4 circuits. Try searching with DG202 to find analog multiplexer variants. This digital multiplexer has 200Ohm internal resistance. The datasheets for the 16 pins explain the functions. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. The analog switch ic is of the Dual, Single supply type and is cost-effective. Put voltage above 100μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 18V. You should attach at least 4.5V voltage if you are using dual power supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. 18V operating voltages are supported by the electronic component.
DG202CSE+ Features
1 Channels
Switch Circuit: SPST - NO
DG202CSE+ Applications
There are a lot of Maxim Integrated DG202CSE+ Analog Switches & Multiplexers ICs applications.
- Cellular phones
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Signal routing between systems
- Digital cross connects (DSX-1)
- Public switching systems
- USB 1.1 signal switching circuits
- PDAs
- Digital access cross connects
- Battery Powered Instruments
- Avionics test equipment
