Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2006 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
200Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG202 |
Pin Count |
16 |
Operating Supply Voltage |
15V |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
25V |
Operating Supply Current |
20μA |
Nominal Supply Current |
20μA |
Max Supply Current |
100μA |
Throw Configuration |
SPST |
Turn On Delay Time |
600 ns |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
450 ns |
Max Dual Supply Voltage |
18V |
On-State Resistance (Max) |
200Ohm |
Min Dual Supply Voltage |
4.5V |
High Level Output Current |
20mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
70 dB |
Current - Leakage (IS(off)) (Max) |
5nA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
600ns, 450ns |
Charge Injection |
20pC |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Voltage - Supply, Dual (V±) |
±4.5V~18V |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG202CSE+T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around 0°C~70°C TA. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. There is an electrical component included in the 16 series. Multiplexers built on a SPST - NO switching circuit are built. The circuits in this analogue multiplexer number 4. Use DG202 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 200Ohm. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. Dual, Single supply type digital switch with a low cost. This multiplexer would work with 20μA current. A voltage higher than 100μA may cause damage to the switch multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 18V. The voltage should be at least 4.5V if you are using dual power supplies. The electronic component can function from 15V.
DG202CSE+T Features
1 Channels
Switch Circuit: SPST - NO
20μA Supply Current
DG202CSE+T Applications
There are a lot of Maxim Integrated DG202CSE+T Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- Audio and video signal routing
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Ultrasound
- PCMCIA cards
- Microwave transmission systems
- DVD-R
- Multi-Line E1 Interface Cards
- Intelligent PBX
- Relay replacements