DG202DY+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 200.686274mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | DG202 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG202DY+ Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. 16 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 16 series. SPST - NO switching circuits are used in these analog switch ics. There are 4 circuits in this switch device. Try searching for the analog switch ic with DG202 if you are looking for variants. A 200Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 16 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 25V volts for the multiplexer. A cost-effective Dual supply type analogue multiplexer. Putting voltage greater than 400μA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 18VWhen using dual power supplies, you should attach at least 4.5V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. This electrical part is compatible with 15V operating voltages.
DG202DY+ Features
1 Channels
Switch Circuit: SPST - NO
DG202DY+ Applications
There are a lot of Maxim Integrated DG202DY+ Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- High reliability control systems
- New designs requiring multiplexer functions
- SONET/SDH ADM
- Data switching
- SONET
- SDH
- Channelized and Unchannelized DS3 applications
- Sample-and-hold systems
- Routers
