DG202DY+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | DG202 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG202DY+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 16 terminations. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. An electrical component of this type can be found in the 16 series. A SPST - NO switching circuit is used to build these analog multiplexers. 4 circuits are used in this analogue multiplexer. Try searching for DG202 variants of the analog switch ic. Analog switches have 200Ohm internal resistance. Datasheets for 16 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. Analogue multiplexer with a Dual, Single supply type that is cost-effective. This digital switch can be operated with a current of 20μA. If put voltage greater than 100μA on the device, damage may be caused to the analogue multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. With dual power supplies, you should attach at least 4.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating voltages range from 15V.
DG202DY+T Features
1 Channels
Switch Circuit: SPST - NO
20μA Supply Current
DG202DY+T Applications
There are a lot of Maxim Integrated DG202DY+T Analog Switches & Multiplexers ICs applications.
- DVD-R
- Audio/video switches
- Video switching
- Microwave transmission systems
- DSLAMs
- Industrial control systems
- FTTH
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Routers
- Frame Relay Equipment
