DG2037DS-T1

30ns, 22ns SPST - NO 5Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 8 Pins 1nA 3V SOT-23-8

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG2037DS-T1
Package: SOT-23-8
Datasheet: PDF
Stock: 287
Description: 30ns, 22ns SPST - NO 5Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 8 Pins 1nA 3V SOT-23-8(Kg)

Details

Tags

Parameters
Mounting Type	Surface Mount
Package / Case	SOT-23-8
Surface Mount	YES
Number of Pins	8
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2009
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	5Ohm
Terminal Finish	TIN LEAD
Subcategory	Multiplexer or Switches
Max Power Dissipation	515mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.635mm
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	30
Output	SEPARATE OUTPUT
Pin Count	8
Qualification Status	Not Qualified
Power Supplies	3/5V
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Nominal Supply Current	20nA
Max Supply Current	1μA
Turn On Delay Time	35 ns
Supply Type	Single
Turn-Off Delay Time	31 ns
On-State Resistance (Max)	5Ohm
Multiplexer/Demultiplexer Circuit	1:1
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	15pF 17pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	30ns, 22ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	200m Ω (Max)
Crosstalk	-67dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	1.8V~5.5V
Normal Position	NO
RoHS Status	Non-RoHS Compliant

DG2037DS-T1 Overview

Shipping overseas is convenient with the electronic component packed in SOT-23-8. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 8. The electronic part delivers high-quality output through its 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the electrical part body. A SPST - NO switching circuit is used for these analog switches. Circuits number 2 make up this analogue multiplexer. A 5Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 8 pins functions. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. A low voltage of 1.8V should be applied to the electronic component. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. A digital multiplexer may suffer damage if voltage is applied above 1μA. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.