DG2038DQ-T1-E3
| Parameters | |
|---|---|
| Terminal Pitch | 0.635mm |
| Base Part Number | DG2038 |
| Output | SEPARATE OUTPUT |
| Power Supplies | 3/5V |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Analog IC - Other Type | DPDT |
| Operating Supply Current | 20nA |
| Nominal Supply Current | 20nA |
| Power Dissipation | 320mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 31 ns |
| On-State Resistance (Max) | 5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 17pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 22ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω (Max) |
| Crosstalk | -67dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 2.5Ohm |
| Normal Position | NC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 320mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
DG2038DQ-T1-E3 Overview
This electronic part is conveniently packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad, making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, there are 8 terminations. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching for DG2038 variants of the analog switch ic. An switch multiplexer with 5Ohm internal resistance has a value of 5Ohm. Datasheets for functions of 8 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Digital switch that provides Single power at a cost-effective price. It is recommended to use 1.8V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 20nA current. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. It is integrated with a DPDT analog IC. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. The electrical component supports 2 inputs. There is 2.5Ohm resistance between Drain and Source for this electronic part.
DG2038DQ-T1-E3 Features
Switch Circuit: SPST - NO
20nA Supply Current
Drain-to-Source resistance: 2.5Ohm
DG2038DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2038DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- SDH
- Audio/video switches
- Residential Gateways, Home Gateway/Router
- Cellular phones
- Microprocessor Controlled Analog Systems
- Public switching systems
- PDH Multiplexers
- High reliability control systems
- Sample-and-hold systems
