DG2039DS-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 515mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Terminal Pitch | 0.635mm |
| Base Part Number | DG2039 |
| Output | SEPARATE OUTPUT |
| Power Supplies | 3/5V |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Analog IC - Other Type | DPDT |
| Operating Supply Current | 20nA |
| Nominal Supply Current | 20nA |
| Power Dissipation | 515mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 31 ns |
| On-State Resistance (Max) | 5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 17pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 30ns, 22ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω (Max) |
| Crosstalk | -67dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2039DS-T1-E3 Overview
The electrical component comes in SOT-23-8 packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 8. A SPST - NO/NC switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with DG2039. As far as internal resistance is concerned, it has 5Ohm. Datasheets for 8 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. 1.8V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 20nA. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. There is an analog IC DPDT integrated with this board. There are SEPARATE OUTPUT outputs on this analog switch ic. Among the inputs that can be operated are the 2 inputs.
DG2039DS-T1-E3 Features
Switch Circuit: SPST - NO/NC
20nA Supply Current
DG2039DS-T1-E3 Applications
There are a lot of Vishay Siliconix DG2039DS-T1-E3 Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- PBXs
- Automatic test equipment
- Microprocessor Controlled Analog Systems
- Routers
- Industrial
- Audio and video signal routing
- Voice over IP/DSL – Integrated Access Devices, Smart
- Data Acquisition Systems
- Audio and video switching
