DG2041DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.5Ohm |
| Terminal Finish | Palladium/Gold (Pd/Au) - with Nickel (Ni) barrier |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.88W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG2041 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | S-XQCC-N16 |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 42 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 32 ns |
| On-State Resistance (Max) | 1.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 63 dB |
| Channel Capacitance (CS(off), CD(off)) | 26pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 42ns, 32ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω (Max) |
| Crosstalk | -93dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 82ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 950μm |
| Length | 4mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2041DN-T1-E4 Overview
This electronic part is conveniently packaged in 16-VQFN Exposed Pad, making it easy to ship abroad. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. With a 2V voltage supply, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Based on SPST - NC switching circuits, these analog multiplexers work. A 4 circuit is present in this switch device. Try searching for the analog switch ic with DG2041 if you are looking for variants. As far as internal resistance is concerned, it has 1.5Ohm. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analog switch ics with Single supply type are cost-effective. 1.8V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 1nA current would be sufficient. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V. When the digital multiplexer is charged above 1μA, damage can occur. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
DG2041DN-T1-E4 Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
DG2041DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2041DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Cable Modem
- Digital cross connects (DSX-1)
- Battery-powered systems
- Mechanical reed relay replacement
- Automatic test equipment
- ISDN NT1/TA
- Cross Connects
- SDH
- Power routing
- Intelligent PBX
