DG2041DQ-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG2041 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 42 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 32 ns |
| On-State Resistance (Max) | 1.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 63 dB |
| Channel Capacitance (CS(off), CD(off)) | 26pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 42ns, 32ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω (Max) |
| Crosstalk | -93dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 82ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2041DQ-T1-E3 Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. 16 terminations have been made so far. A 1 channel electronic part produces high-quality output. A 2V voltage supply should turn on and run the electronic component. The electrical component body receives 16 pins. Based on SPST - NC switching circuits, these analog multiplexers work. It consists of 4 circuits. Try searching for DG2041 variants of the analog switch ic. Analog switches have 1.5Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 1.8V. It would be sufficient to run this analogue multiplexer with 1nA current. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. A digital multiplexer may suffer damage if voltage is applied above 1μA. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
DG2041DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
DG2041DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2041DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Isolation
- Video signal routing
- Medical
- PBX interfaces
- Cell phones
- Microprocessor controlled systems
- Frame Relay Equipment
- Battery Powered Instruments
