DG2042DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.5Ohm |
| Terminal Finish | PALLADIUM GOLD OVER NICKEL |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.88W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG2042 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 1.88W |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 42 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 32 ns |
| On-State Resistance (Max) | 1.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 63 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 26pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 42ns, 32ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω (Max) |
| Crosstalk | -93dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 82ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Height | 950μm |
| Length | 4mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG2042DN-T1-E4 Overview
Presented in 16-VQFN Exposed Pad, this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. A total of 16 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. Powered by a 2V voltage supply, the electrical part should be switched on and run. This electronic part can be found in the 16 series. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching for DG2042 variants of the analog switch ic. Analog switches have 1.5Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users shouldn't supply more than 5.5V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. The lowest voltage the electronic part should receive is 1.8V. An operating current of 1nA would be sufficient for this switch device. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V. It may damage the digital multiplexer if the voltage is higher than 1μA. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. It is possible to operate 4 inputs.
DG2042DN-T1-E4 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
DG2042DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2042DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- Multi-Line E1 Interface Cards
- Communications systems
- Industrial and process control systems
- Video signal routing
- High reliability control systems
- 65 V DACs
- High speed data transmission line cards
- Routers
- Medical systems
