DG2043DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.5Ohm |
| Terminal Finish | PALLADIUM GOLD OVER NICKEL |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.88W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG2043 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 42 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 32 ns |
| On-State Resistance (Max) | 1.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 63 dB |
| Channel Capacitance (CS(off), CD(off)) | 26pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 42ns, 32ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω (Max) |
| Crosstalk | -93dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 82ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 950μm |
| Length | 4mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG2043DN-T1-E4 Overview
Due to its 16-VQFN Exposed Pad packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. In total, there are 16 terminations. Due to its 1 channels, the electrical component produces high-quality output. An 2V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 16 series. SPST - NO/NC switching circuits are used in these analog switch ics. The multiplexer consists of 4 circuits. Try searching with DG2043 if you're looking for variants. There is 1.5Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 1.8V. This digital switch can be operated with a current of 1nA. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
DG2043DN-T1-E4 Features
1 Channels
Switch Circuit: SPST - NO/NC
1nA Supply Current
DG2043DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2043DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Public switching systems
- SDH/SONET multiplexers
- Digital Cross-Connects
- Industrial control systems
- Cell phones
- Battery Powered Instruments
- Wireless Local Loop
- 65 V DACs
- Precision instrumentation
- DSLAMs
