DG2043DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG2043 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 42 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 32 ns |
| On-State Resistance (Max) | 1.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 63 dB |
| Channel Capacitance (CS(off), CD(off)) | 26pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 42ns, 32ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω (Max) |
| Crosstalk | -93dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 82ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
DG2043DQ-T1-E3 Overview
The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 16. The electronic part delivers high-quality output through its 1 channels. It is safe to turn on and run the electronic component with a 2V voltage supply. It is injected into the electrical part body with 16 pins. Based on SPST - NO/NC switching circuits, these analog multiplexers work. Circuits number 4 make up this analogue multiplexer. Try searching with DG2043 if you're looking for variants. The internal resistance of this digital multiplexer is 1.5Ohm. Datasheets for 16 pin functions are available upon request. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 5.5V in normal situations. A cost-effective Single supply type analogue multiplexer. It is recommended to use 1.8V as the lowest voltage for the electrical part. The switch device would be able to operate with 1nA current. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. When the digital multiplexer is charged above 1μA, damage can occur. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
DG2043DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
1nA Supply Current
DG2043DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2043DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Automotive applications
- USB 1.1 signal switching circuits
- Medical Instrumentation
- Imaging
- DVD-R
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- ATM
- Relay Replacement
- Isolation
- Audio/video switches
