DG211BDJ-E3

300ns, 200ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG211 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG211BDJ-E3
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 185
Description: 300ns, 200ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG211 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Weight	1.627801g
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2005
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	470mW
Technology	CMOS
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG211
Pin Count	16
Polarity	Non-Inverting
Power Supplies	512/+-15V
Number of Channels	1
Max Supply Voltage	25V
Min Supply Voltage	4.5V
Operating Supply Current	10μA
Nominal Supply Current	50μA
Power Dissipation	470mW
Max Supply Current	10μA
Throw Configuration	SPST
Turn On Delay Time	300 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	4.5V~25V ±4.5V~22V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	200 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	4.5V
High Level Output Current	100mA
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	300ns, 200ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	50Ohm
Normal Position	NC
Height	3.81mm
Length	21.33mm
Width	7.11mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG211BDJ-E3 Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. It is mounted in the position Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Extended operating temperature around -40°C~85°C TA. There are 16 terminations totally. A 1 channel electronic part produces high-quality output. A 15V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. A SPST - NC switching circuit is used to build these analog multiplexers. Use DG211 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 160Ohm. You can find the functions of the 16 pins in the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 25V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 4.5V should be applied to the electronic component. An operating current of 10μA would be sufficient for this switch device. If put voltage greater than 10μA on the device, damage may be caused to the analogue multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. In the case of dual power supplies, you should connect at least 4.5V. It is possible to operate 4 inputs. There is 50Ohm Drain to Source resistance on this electronic part.