Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2016 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG211 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
22V |
Power Supplies |
512/+-15V |
Number of Channels |
1 |
Max Supply Voltage |
25V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
10μA |
Nominal Supply Current |
50μA |
Power Dissipation |
640mW |
Throw Configuration |
SPST |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
4.5V~25V ±4.5V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
300ns, 200ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
300ns |
Switch-off Time-Max |
200ns |
Normal Position |
NC |
Height Seated (Max) |
1.2mm |
Length |
5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG211BDQ-E3 Overview
The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -40°C~85°C TA. In total, 16 terminations have occurred. This electronic part offers high-quality output due to its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. This electronic part can be found in the 16 series. The analog switch ics are built using SPST - NC switching circuits. DG211 can be used to search for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 160Ohm. The functions of 16 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 25V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 4.5V. An operating current of 10μA would be sufficient for this switch device. There is no problem with using dual supply voltage, but it should not exceed 22V. It is recommended that you attach at least 4.5V to your dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. Operating voltages range from 22V. Among the inputs that can be operated are the 4 inputs.
DG211BDQ-E3 Features
1 Channels
Switch Circuit: SPST - NC
10μA Supply Current
DG211BDQ-E3 Applications
There are a lot of Vishay Siliconix DG211BDQ-E3 Analog Switches & Multiplexers ICs applications.
- Industrial
- Audio and video switching
- Fiber In The Loop (FITL)
- Digital access cross connects
- Communications systems
- Relay Replacement
- Mechanical reed relay replacement
- Automotive applications
- Audio/video switches
- Avionics and Military Systems