DG211BDQ-T1-E3

300ns, 200ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG211 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG211BDQ-T1-E3
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 505
Description: 300ns, 200ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG211 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG211
Output	SEPARATE OUTPUT
Pin Count	16
Power Supplies	512/+-15V
Number of Channels	1
Max Supply Voltage	25V
Min Supply Voltage	4.5V
Operating Supply Current	10μA
Nominal Supply Current	50μA
Power Dissipation	640mW
Max Supply Current	10μA
Throw Configuration	SPST
Turn On Delay Time	300 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	4.5V~25V ±4.5V~22V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	200 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	300ns, 200ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Normal Position	NC
Height	920μm
Length	5.08mm
Width	4.4mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	640mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4

DG211BDQ-T1-E3 Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Totally, there are 16 terminations. A electrical component with 1 channels is capable of high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. This electrical component is included in the 16 series of products. Circuits based on SPST - NC switching are used to construct these analog switch ics. Using the DG211 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 160Ohm. Datasheets for functions of 16 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 25V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 4.5V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 10μA. If put voltage greater than 10μA on the device, damage may be caused to the analogue multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. For dual power supplies, a voltage of at least 4.5V should be attached. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. In order to operate the 4 inputs, there are several steps to follow.