DG211BDY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Bulk |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 1.27mm |
| Pin Count | 16 |
| Polarity | Inverting |
| Power Supplies | 512/+-15V |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 30mA |
| Nominal Supply Current | 30mA |
| Power Dissipation | 640mW |
| Max Supply Current | 10μA |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 85Ohm |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG211BDY Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Bulk is used. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. In total, 16 terminations have occurred. It is injected into the electrical part body with 16 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. This digital multiplexer has 85Ohm internal resistance. Please refer to the datasheets for 16 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended to use 4.5V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 30mA. If you put voltage higher than 10μA on the digital multiplexer, damage may occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. When using dual power supplies, you should attach at least 4.5V. There are 4 inputs to be operated. There is 85Ohm resistance between the Drain and Source on this part.
DG211BDY Features
Switch Circuit: SPST - NC
30mA Supply Current
Drain-to-Source resistance: 85Ohm
DG211BDY Applications
There are a lot of Vishay Siliconix DG211BDY Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- Frame Relay Equipment
- ATM
- Audio signal routing
- E1 Network Equipment
- Mechanical reed relay replacement
- Medical
- SDH/SONET multiplexers
- Medical systems
- Cable Modem
