DG211BDY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Power Dissipation | 640mW |
| Max Supply Current | 10μA |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG211BDY-T1 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature around -40°C~85°C TA extended. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 16 pins are injected into the electrical part body. The analog switch ics are built using SPST - NC switching circuits. A 85Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 16 pins functions. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual, Single supply type. In order for the electronic part to function properly, the lowest voltage should be 4.5V. The analogue multiplexer may be damaged if voltage is greater than 10μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. If you are using dual power supplies, you should attach at least 4.5V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. A 4 input needs to be operated.
DG211BDY-T1 Features
1 Channels
Switch Circuit: SPST - NC
DG211BDY-T1 Applications
There are a lot of Vishay Siliconix DG211BDY-T1 Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Cross Connects
- Battery Powered Systems
- Mechanical reed relay replacement
- Audio signal routing
- Public switching systems
- Channelized and Unchannelized DS3 applications
- Avionics test equipment
- Cellular phones
- PCMCIA cards
