DG211CJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG211 |
| Pin Count | 16 |
| Output Type | Adjustable |
| Operating Supply Voltage | 18V |
| Number of Channels | 4 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Drain to Source Resistance | 175Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG211CJ+ Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around 0°C~70°C TA are extended for operation. In total, there are 16 terminations. A 4 channel electronic part produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 16 pins. A SPST - NC switching circuit is used to build these analog multiplexers. Search with DG211 if you are looking for analog multiplexer variants. There is 175Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. The digital multiplexer has a low cost Dual supply. The switch device would be able to operate with 20μA current. The analogue multiplexer may be damaged if voltage is greater than 20μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. You should attach at least 4.5V voltage if you are using dual power supply. 18V operating voltages are supported by the electronic component. This electronic component presents a Drain to Source resistance of 175Ohm.
DG211CJ+ Features
4 Channels
Switch Circuit: SPST - NC
20μA Supply Current
Drain-to-Source resistance: 175Ohm
DG211CJ+ Applications
There are a lot of Maxim Integrated DG211CJ+ Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- T1/E1 Terminals
- Private Branch Exchange (PBX)
- FTTH
- MP3 players
- Remote Powered Equipment
- Modems
- DSLAMs
- Automotive applications
- Video switching
