DG211CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG211 |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5+-15V |
| Number of Channels | 4 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Drain to Source Resistance | 175Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG211CSE+ Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of 0°C~70°C TA degrees Celsius. In total, there are 16 terminations. The electronic part delivers high-quality output through its 4 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. This electrical component is included in the 16 series of products. These analog multiplexers are built based on SPST - NC switching circuits. Use DG211 to search for variants of the digital switches. An switch multiplexer with 175Ohm internal resistance has a value of 175Ohm. You can find the functions of the 16 pins in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. A cost-effective Dual supply type analogue multiplexer. For this multiplexer to operate, 20μA current would be sufficient. When the digital multiplexer is charged above 20μA, damage can occur. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 4.5V. It can operate from 18V operating voltages. This electronic component presents a Drain to Source resistance of 175Ohm.
DG211CSE+ Features
4 Channels
Switch Circuit: SPST - NC
20μA Supply Current
Drain-to-Source resistance: 175Ohm
DG211CSE+ Applications
There are a lot of Maxim Integrated DG211CSE+ Analog Switches & Multiplexers ICs applications.
- Residential Gateways, Home Gateway/Router
- ATM
- Fiber to the Home
- Modems
- Automotive applications
- Power routing
- Remote wireless modules
- High-Voltage
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Video switching
