DG211CUE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 755mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG211 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG211CUE+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around 0°C~70°C TA. 16 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. The electronic part body is injected with 16 pins. SPST - NC switching circuits are used in these analog switch ics. It consists of 4 circuits. Try searching for DG211 variants of the analog switch ic. In this multiplexer, the internal resistance is 175Ohm. Please refer to the datasheets for 16 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. Analogue multiplexers of the Dual supply type that are cost-effective. For this digital switch to work, 20μA current would suffice. Put voltage above 400μA on the multiplexer to cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 18V. The voltage should be at least 4.5V if you are using dual power supplies. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. A voltage of 15V can be used to operate the electronic component.
DG211CUE+ Features
1 Channels
Switch Circuit: SPST - NC
20μA Supply Current
DG211CUE+ Applications
There are a lot of Maxim Integrated DG211CUE+ Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Sample-and-hold systems
- Routers
- Frame Relay Equipment
- Microprocessor Controlled Analog Systems
- Cellular phones
- Voice over IP/DSL – Integrated Access Devices, Smart
- Low-Voltage
- Intelligent PBX
- High-Voltage
