DG211DY+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG211 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG211DY+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. A total of 16 terminations have been recorded. By its 4 channels, the electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. As part of its design, the 16 series is equipped with this electronic component. Multiplexers built on a SPST - NC switching circuit are built. Look for analog switch ic variants by searching with DG211. In this multiplexer, the internal resistance is 175Ohm. You can find the functions of the 16 pins in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 18V in normal situations. A analog switch ic that has a cost-effective Dual supply type. A low voltage of 4.5V should be applied to the electronic component. For this multiplexer to operate, 20μA current would be sufficient. The switch multiplexer may be damaged if it is exposed to voltage greater than 400μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. A dual power supply should have at least 4.5V voltage attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG211DY+ Features
4 Channels
Switch Circuit: SPST - NC
20μA Supply Current
DG211DY+ Applications
There are a lot of Maxim Integrated DG211DY+ Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- High speed data transmission line cards
- ATM
- PBXs
- Switching Systems
- 65 V DACs
- PCMCIA cards
- Fault Tolerant Systems
- Audio and video routing
- Avionics test equipment
