DG211EUE+
| Parameters | |
|---|---|
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 755mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG211 |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switch-on Time-Max | 1000ns |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
DG211EUE+ Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 16. As a result of its 1 channels, this electronic component provides high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. There is an electrical component included in the 16 series. The analog switch ics are built using SPST - NC switching circuits. A total of 4 circuits make up this switch device. If you are looking for variants of the digital switch, trying search with DG211. A 175Ohm internal resistance characterizes this multiplexer. To find out what the 16 pins do, please refer to the datasheets. Multiplexers should not be powered above 18V in normal situations. Analogue multiplexer with a Dual supply type that is cost-effective. 4.5V is the lowest voltage that should be fed to the electronic electronic part. In order to operate this switch device, it would need a current of 20μA. When the digital multiplexer is charged above 400μA, damage can occur. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 4.5V.
DG211EUE+ Features
1 Channels
Switch Circuit: SPST - NC
20μA Supply Current
DG211EUE+ Applications
There are a lot of Maxim Integrated DG211EUE+ Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- HDTV
- Switching Systems
- SONET/SDH ADM
- PDAs
- SONET
- PBXs
- Medical
- Digital access cross connects
- DSLAMs
