DG212BDJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 512/+-15V |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Power Dissipation | 470mW |
| Max Supply Current | 10μA |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 85Ohm |
| Normal Position | NO |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
DG212BDJ Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. In total, there are 16 terminations. As part of its design, the 16 series is equipped with this electronic component. Unlike digital switches, these are based on SPST - NO switching circuits. A 85Ohm internal resistance characterizes this multiplexer. The functions of 16 pins can be found in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 25V. Digital switch that provides Dual, Single power at a cost-effective price. In order for the electronic part to function properly, the lowest voltage should be 4.5V. The analogue multiplexer may be damaged if voltage is greater than 10μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. With dual power supplies, you should attach at least 4.5V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Operating the 4 inputs requires 4 inputs. Resistivity from Drain to Source is 85Ohm for this electronic part.
DG212BDJ Features
Switch Circuit: SPST - NO
Drain-to-Source resistance: 85Ohm
DG212BDJ Applications
There are a lot of Vishay Siliconix DG212BDJ Analog Switches & Multiplexers ICs applications.
- Communication systems
- Avionics
- High speed data transmission line cards
- Remote Powered Equipment
- E1 Network Equipment
- Multi-Line E1 Interface Cards
- Data Acquisition Systems
- PBXs
- Audio and video signal routing
- Audio and video routing
