DG212BDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-PDIP |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2015 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 160Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 470mW |
| Base Part Number | DG212 |
| Number of Outputs | 4 |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 50μA |
| Power Dissipation | 470mW |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2Ohm |
| Crosstalk | -95dB @ 100kHz |
| Drain to Source Resistance | 50Ohm |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG212BDJ-E3 Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. In Through Hole, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. A electrical component with 4 channels is capable of high-quality output. Based on SPST - NO switching circuits, these analog multiplexers work. Circuits number 4 make up this analogue multiplexer. Try searching for the analog switch ic with DG212 if you are looking for variants. A 160Ohm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. An effective Dual, Single supply digital multiplexer. 4.5V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 10μA. It may damage the digital multiplexer if the voltage is higher than 10μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 4.5V. It is possible to operate 4 inputs. Temperatures higher than 85°C are not recommended for operation of the analogue multiplexer. There is 50Ohm resistance between the Drain and Source on this part. 4 outputs are included in the analogue multiplexer. Suppliers are offering a 16-PDIP package.
DG212BDJ-E3 Features
4 Channels
Switch Circuit: SPST - NO
10μA Supply Current
Drain-to-Source resistance: 50Ohm
DG212BDJ-E3 Applications
There are a lot of Vishay Siliconix DG212BDJ-E3 Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- RGB switches
- DSUs
- Automatic test equipment
- Digital access cross connects
- T1/E1 Terminals
- Channelized and Unchannelized DS3 applications
- HDTV
- PCMCIA cards
- Medical
