DG212BDQ-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-TSSOP |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 160Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 640mW |
| Base Part Number | DG212 |
| Number of Outputs | 4 |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 50μA |
| Power Dissipation | 640mW |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2Ohm |
| Crosstalk | -95dB @ 100kHz |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG212BDQ-T1-E3 Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. The electronic part provides high-quality output because it has 4 channels. SPST - NO switching circuits are used in these analog switch ics. There are 4 circuits in this switch device. DG212 can be used to search for analog multiplexer variants. There is 160Ohm internal resistance in this digital multiplexer. The datasheets for the 16 pins explain the functions. A voltage higher than 25V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. 4.5V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 10μA would be sufficient for this switch device. It may damage the digital multiplexer if the voltage is higher than 10μA. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIt is recommended that you attach at least 4.5V to your dual power supply. The 4 inputs need to be operated in order to work. The switches should not operate in an environment where the temperature is higher than 85°C. The analog switch ics includes 4 outputs. Suppliers offer the 16-TSSOP package.
DG212BDQ-T1-E3 Features
4 Channels
Switch Circuit: SPST - NO
10μA Supply Current
DG212BDQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG212BDQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- Digital access cross connects
- Sample-and-hold systems
- New designs requiring multiplexer functions
- Relay Replacement
- Power routing
- Imaging
- 65 V DACs
- Audio and video switching
- Avionics and Military Systems
