Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2005 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
160Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG212 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
512/+-15V |
Number of Channels |
1 |
Max Supply Voltage |
25V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
10μA |
Nominal Supply Current |
50μA |
Power Dissipation |
640mW |
Max Supply Current |
10μA |
Throw Configuration |
SPST |
Turn On Delay Time |
300 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
4.5V~25V ±4.5V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
300ns, 200ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG212BDY-E3 Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. 16 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching for the analog switch ic with DG212 if you are looking for variants. Analog switches have 160Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 25V. Digital switch that provides Dual, Single power at a cost-effective price. There should be 4.5V voltage fed to the electrical part below 4.5V. The analogue multiplexer could operate on 10μA current. If put voltage greater than 10μA on the device, damage may be caused to the analogue multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIf you are using a dual power supply, you should attach at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic. It is possible to operate 4 inputs.
DG212BDY-E3 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
DG212BDY-E3 Applications
There are a lot of Vishay Siliconix DG212BDY-E3 Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Avionics and Military Systems
- High speed data transmission line cards
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fault Tolerant Systems
- Relay Replacement
- Digital cross connects (DSX-1)
- Video switching
- Relay replacements
- DSUs