DG212BDY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Power Dissipation | 640mW |
| Max Supply Current | 10μA |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG212BDY-T1 Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~85°C TA. There are 16 terminations totally. The electronic part provides high-quality output because it has 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. 16 pins are injected to the electronic part body. A SPST - NO switching circuit is used to build these analog multiplexers. A 85Ohm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. Users shouldn't supply more than 25V voltage to the switch device. Analog switch ics with Dual, Single supply type are cost-effective. 4.5V is the lowest voltage that should be fed to the electronic electronic part. A digital multiplexer may suffer damage if voltage is applied above 10μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. In the case of dual power supplies, you should connect at least 4.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. There are 4 inputs to be operated.
DG212BDY-T1 Features
1 Channels
Switch Circuit: SPST - NO
DG212BDY-T1 Applications
There are a lot of Vishay Siliconix DG212BDY-T1 Analog Switches & Multiplexers ICs applications.
- Modems
- DSUs
- Microprocessor controlled systems
- Private Branch Exchange (PBX)
- Low-Voltage
- Digital cross connects (DSX-1)
- Remote Powered Equipment
- High reliability control systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fault Tolerant Systems
