DG212CJ
| Parameters | |
|---|---|
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Drain to Source Resistance | 175Ohm |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG212 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5+-15V |
| Number of Channels | 4 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
DG212CJ Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. Total terminations are 16. By its 4 channels, the electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 16 series. A SPST - NO switching circuit is used to build these analog multiplexers. Use DG212 to search for variants of the digital switches. A 175Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. The digital multiplexer has a low cost Dual supply. An operating current of 20μA would be sufficient for this switch device. When the digital multiplexer is charged above 20μA, damage can occur. Despite this switch device's dual supply capability, its voltage should not exceed 18V. In the case of dual power supplies, you should connect at least 4.5V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. It can operate from 18V operating voltages. The Drain to Source resistance of this electronic component is 175Ohm.
DG212CJ Features
4 Channels
Switch Circuit: SPST - NO
20μA Supply Current
Drain-to-Source resistance: 175Ohm
DG212CJ Applications
There are a lot of Maxim Integrated DG212CJ Analog Switches & Multiplexers ICs applications.
- Routers
- Isolation
- Modems
- Channel Banks
- SONET
- Remote Powered Equipment
- Wireless Local Loop
- Battery Powered Systems
- USB 1.1 signal switching circuits
- Channelized and Unchannelized DS3 applications
