DG212CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG212 |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5+-15V |
| Number of Channels | 4 |
| Nominal Supply Current | 20μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Drain to Source Resistance | 175Ohm |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG212CSE+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tube is used to provide high reliability. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 1:1. Extended operating temperature around 0°C~70°C TA. The total number of terminations is 16. This electronic part offers high-quality output due to its 4 channels. A 15V voltage supply should turn on and run the electronic component. A total of 16 pins are injected into the body of the electronic part. A SPST - NO switching circuit is used for these analog switches. Look for analog switch ic variants by searching with DG212. A 175Ohm internal resistance characterizes this multiplexer. The functions of 16 pins can be found in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. The digital multiplexer has a low cost Dual supply. A voltage higher than 20μA may cause damage to the switch multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 18V. You should attach at least 4.5V voltage if you are using dual power supply. This electrical part is compatible with 18V operating voltages. Resistivity from Drain to Source is 175Ohm for this electronic part.
DG212CSE+ Features
4 Channels
Switch Circuit: SPST - NO
Drain-to-Source resistance: 175Ohm
DG212CSE+ Applications
There are a lot of Maxim Integrated DG212CSE+ Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Data switching
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Access Concentrators
- Audio and video routing
- Avionics test equipment
- Cable Modem
- Central office
- Channel Banks
- Cell phones
