DG212CY+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | DG212 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG212CY+ Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tube provides high reliability. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operational temperature extended around 0°C~70°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. A 15V voltage supply should turn on and run the electronic component. An injection of 16 pins is performed into the body of the electrical component. A SPST - NO switching circuit is used to build these analog multiplexers. There are 4 circuits in this switch device. Try searching with DG212 if you're looking for variants. An switch multiplexer with 175Ohm internal resistance has a value of 175Ohm. Please refer to the datasheets for 16 pins functions. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 18V. An effective Dual supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 4.5V. An operating current of 20μA would be sufficient for this switch device. Put voltage above 400μA on the multiplexer to cause damage. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. It is recommended that you attach at least 4.5V to your dual power supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG212CY+ Features
1 Channels
Switch Circuit: SPST - NO
20μA Supply Current
DG212CY+ Applications
There are a lot of Maxim Integrated DG212CY+ Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- PBXs
- DSUs
- PDH Multiplexers
- Cellular phones
- Relay replacements
- Fault Tolerant Systems
- Frame Relay Equipment
- Isolation
- Switching Systems
