DG212DJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG212 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG212DJ+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around -40°C~85°C TA. 16 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. A total of 16 pins are injected into the electrical part body. A SPST - NO switching circuit is used for these analog switches. The multiplexer consists of 4 circuits. Try searching with DG212 to find analog multiplexer variants. There is 175Ohm internal resistance in this digital multiplexer. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 18V voltage to the switch device. An effective Dual supply digital multiplexer. There should be 4.5V voltage fed to the electrical part below 4.5V. It would be sufficient to run this analogue multiplexer with 20μA current. It may damage the digital multiplexer if the voltage is higher than 400μA. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. You should attach at least 4.5V voltage if you are using dual power supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
DG212DJ+ Features
1 Channels
Switch Circuit: SPST - NO
20μA Supply Current
DG212DJ+ Applications
There are a lot of Maxim Integrated DG212DJ+ Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Transmit
- Private Branch Exchange (PBX)
- Precision data acquisition
- Relay Replacement
- CSU
- Signal routing between systems
- Power routing
- DSUs
- Cellular phones
