DG212DY+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | DG212 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG212DY+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tube. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 4 channels. With a 15V voltage supply, the electrical component should be turned on and run. The electrical component body receives 16 pins. These analog multiplexers are built based on SPST - NO switching circuits. If you are looking for variants of the digital switch, trying search with DG212. The internal resistance of this digital multiplexer is 175Ohm. To find out what the 16 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 18V to a switch device. Analog switch ics with Dual supply type are cost-effective. 4.5V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 20μA. A digital multiplexer may suffer damage if voltage is applied above 400μA. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. You should attach at least 4.5V voltage if you are using dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
DG212DY+ Features
4 Channels
Switch Circuit: SPST - NO
20μA Supply Current
DG212DY+ Applications
There are a lot of Maxim Integrated DG212DY+ Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Low-Voltage
- Central office
- Public switching systems
- Fiber In The Loop (FITL)
- Data Acquisition Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Systems
- Sample-and-hold systems
- Communications systems
