DG212DY+T
| Parameters | |
|---|---|
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | DG212 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
DG212DY+T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operational temperature extended around -40°C~85°C TA. In total, there have been 16 terminations. This electronic part offers high-quality output due to its 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. These analog multiplexers are built based on SPST - NO switching circuits. A total of 4 circuits make up this switch device. Search with DG212 if you are looking for analog multiplexer variants. There is 175Ohm internal resistance in this digital multiplexer. Multiplexer or Switches is a typical switch device. Analog switch ics with Dual supply type are cost-effective. An operating current of 20μA would be sufficient for this switch device. The switch multiplexer may be damaged if it is exposed to voltage greater than 400μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. With dual power supplies, you should attach at least 4.5V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electronic component can function from 15V.
DG212DY+T Features
1 Channels
Switch Circuit: SPST - NO
20μA Supply Current
DG212DY+T Applications
There are a lot of Maxim Integrated DG212DY+T Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Residential Gateways, Home Gateway/Router
- New designs requiring multiplexer functions
- RGB switches
- High reliability control systems
- Data Acquisition Systems
- PCMCIA cards
- Sample hold systems
- Public switching systems
- Cable PC
