DG212ETE+
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.177W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.8mm |
| Base Part Number | DG212 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 0.8mm |
| Length | 5mm |
| Width | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG212ETE+ Overview
Due to its 16-WQFN Exposed Pad packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. This electronic part offers high-quality output due to its 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. There is an electrical component included in the 16 series. Based on SPST - NO switching circuits, these analog multiplexers work. There are 4 circuits in this switch device. Search with DG212 if you are looking for analog multiplexer variants. It has an internal resistance of 175Ohm. You can find the functions of the 16 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Analogue multiplexer with a Dual supply type that is cost-effective. For this digital switch to work, 20μA current would suffice. Putting voltage greater than 400μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 18V. The voltage should be at least 4.5V if you are using dual power supplies. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. It can operate from 15V operating voltages.
DG212ETE+ Features
1 Channels
Switch Circuit: SPST - NO
20μA Supply Current
DG212ETE+ Applications
There are a lot of Maxim Integrated DG212ETE+ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- HDTV
- SDH/SONET multiplexers
- PDAs
- DSLAMs
- Fiber to the Home
- PBXs
- Signal routing between systems
- Switching Systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
