DG212ETE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.177W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.8mm |
| Base Part Number | DG212 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 0.8mm |
| Length | 5mm |
| Width | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG212ETE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-WQFN Exposed Pad. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around -40°C~85°C TA. In total, there have been 16 terminations. By its 1 channels, the electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. Electronic part bodies are injected with 16 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. It consists of 4 circuits. Look for analog switch ic variants by searching with DG212. An switch multiplexer with 175Ohm internal resistance has a value of 175Ohm. The datasheets for the 16 pins explain the functions. Theswitch device is a typical Multiplexer or Switches. Analog switch ics with Dual supply type are cost-effective. An operating current of 20μA would be sufficient for this switch device. The analogue multiplexer may be damaged if voltage is greater than 400μA. Despite this switch's dual supply capability, its voltage should not exceed 18V. You should attach at least 4.5V voltage if you are using dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Operating voltages of 15V are compatible with the electrical part.
DG212ETE+T Features
1 Channels
Switch Circuit: SPST - NO
20μA Supply Current
DG212ETE+T Applications
There are a lot of Maxim Integrated DG212ETE+T Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Public switching systems
- Fiber to the Home
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Communications systems
- Medical
- Digital Cross-Connects
- Sample hold systems
- Private Branch Exchange (PBX)
- Microprocessor Controlled Analog Systems
