DG213DJ-E3
| Parameters | |
|---|---|
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 110Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG213 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Power Dissipation | 470mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~40V ±3V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 100ns |
| Charge Injection | 1pC |
DG213DJ-E3 Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. There is an electrical component included in the 16 series. The analog switch ics are built using SPST - NO/NC switching circuits. Try searching with DG213 to find analog multiplexer variants. Analog switches have 110Ohm internal resistance. The datasheets for the 16 pins explain the functions. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 40V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage fed to the electronic component should be 3V. It would be sufficient to run this analogue multiplexer with 1μA current. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 22V. If you are using dual power supplies, you should attach at least 3V. This analog switch ic utilizes SEPARATE OUTPUT output. Operating the 4 inputs requires 4 inputs.
DG213DJ-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
DG213DJ-E3 Applications
There are a lot of Vishay Siliconix DG213DJ-E3 Analog Switches & Multiplexers ICs applications.
- Cellular phones
- High-Voltage
- Audio and video routing
- Audio/video switches
- New designs requiring multiplexer functions
- Automatic test equipment
- SDH/SONET multiplexers
- PBX interfaces
- PDAs
- Battery Powered Instruments
